C2128-00002 Printer Parts Diagram


C2128-00002 is represented by #15 in the diagram below. C4549-60036 Plate Pressure Plate Assembly - Holds media to be printed against the Paper Input Feed Rollers 1 C4549-40028 Arm Lever arm - Used to lift the pressure plate lifter 10 C4562-60065 Chassis Chassis assembly - The large plastic item that forms the base of the print mechanism 11 C4549-40006 Lifter Lifter shaft - Plate like shaft that lifts the pressure plate 12 C2128-00006 Spring Separator spring - Provides pressure between the separator assembly and the center drive roller 13 C2170-00008 Bracket Right bracket - Carriage rod adjustment bracket (Right) 14 C2128-40032 Cap Center lifter cap - Holds the pressure plate lifter and the kicker spring in place 15 C2128-00002 Spring Kicker spring - Provides tension for the kicker 16 C2128-40015 Cap Left lifter cap - Holds the pressure plate lifter in place 18 C2124-20008 Spring Limiter spring - Provides tension for rotation limiter 19 C4562-40022 Limiter Rotation limiter - Provides correct pressure to cap pen 2 C2128-40055 Adjuster PPS adjuster - Used to adjust the distance between the pivot and the pen 21 C2162-40105 Lever Switch lever - Actuates access door (Open) switch 22 C4549-40017 Stop Right wall stop - Maintains alignment of small media sizes in the input tray 23 C4549-67806 Roller Pivot assembly - Large plastic item with large rollers - Picks and feeds media through print mechanism 24 C2162-67802 Stop Paper width adjustment stop - Adjusts for input paper width 25 C4549-40027 Actuator Clutch actuator - Pulls the clutch against the drive gear which starts the media picking process 26 C6450-40011 Spitton Spittoon - Holds ink expelled from cartridge during refresh cycle 27 C2162-40002 Gear Cluster gear for HP DeskJet 500 Series 28 C2162-20004 Spring Pivot spring - Provides tension for pivot to return to upright position 3 C2124-20001 Rail Rear rail - Supports carriage assembly 30 C2124-00009 Spring Spring - Installed in spittoon assembly 31 C2162-60009 Cable Cable assembly - Has 5-pin (F) connector on each end - 26.5cm (10.4in) long 32 C2162-67806 Spring Preloader - Applies downward pressure on drive shaft 33 C6450-60102 Sled Service station sled assembly - Mounts on top of the service station - Performs capping and wiping functions for the print cartridges 34 C6450-80052 Absorber Spittoon sponge - located in bottom of spittoon 35 C2124-20004 Spring Belt spring - For belt tension bracket 36 C2162-40036 Support Flex Support - Supports Flex Circuitry of Carriage Assembly 37 C2164-60045 Motor Paper stepper motor assembly (does NOT include cable) 38 C2124-80008 Strip Encoder strip - Clear strip with position marks - Used by the sensor in the carriage assembly to determine position 39 C2165-00001 Bracket Left bracket - Carriage rod adjustment bracket (Left) 4 C2128-40019 Peg Separator Peg - Lifts the separator pad when the lifter shaft lifts 40 C2128-60018 Separator Separator pad assembly 41 C4562-40032 Bracket Belt tension bracket - Pivot bracket for idler pulley - Applies tension to the carriage belt 42 C2124-00001 Spring Encoder spring - Provides tension for encoder strip 43 C2164-00015 Clip Carriage shaft retainer clip 44 C2162-40016 Hub Idler hub - Drive belt pivot point on left side of chassis 46 C2162-20005 Rod Carriage rod - Supports horizontal carriage movement 47 C2128-40020 Kicker Kicker - Straightens the stack of media in the input tray so that the separator can function consistently 48 C2164-40060 Belt Carriage belt for HP DeskJet 550C Series 6 C2124-60116 Roller Lower pinch roller 7 C4549-40029 Lifter Separator lifter 8 C2162-60006 Motor Carriage motor assembly (includes cable) 9 C2145-00017 Spring Lever arm spring - Provides tension between the lever arm and the pressure plate lifter

C4549-60036 Plate Pressure Plate Assembly - Holds media to be printed against the Paper Input Feed Rollers

1

C4549-40028 Arm Lever arm - Used to lift the pressure plate lifter

10

C4562-60065 Chassis Chassis assembly - The large plastic item that forms the base of the print mechanism

11

C4549-40006 Lifter Lifter shaft - Plate like shaft that lifts the pressure plate

12

C2128-00006 Spring Separator spring - Provides pressure between the separator assembly and the center drive roller

13

C2170-00008 Bracket Right bracket - Carriage rod adjustment bracket (Right)

14

C2128-40032 Cap Center lifter cap - Holds the pressure plate lifter and the kicker spring in place

15

C2128-00002 Spring Kicker spring - Provides tension for the kicker

16

C2128-40015 Cap Left lifter cap - Holds the pressure plate lifter in place

18

C2124-20008 Spring Limiter spring - Provides tension for rotation limiter

19

C4562-40022 Limiter Rotation limiter - Provides correct pressure to cap pen

2

C2128-40055 Adjuster PPS adjuster - Used to adjust the distance between the pivot and the pen

21

C2162-40105 Lever Switch lever - Actuates access door (Open) switch

22

C4549-40017 Stop Right wall stop - Maintains alignment of small media sizes in the input tray

23

C4549-67806 Roller Pivot assembly - Large plastic item with large rollers - Picks and feeds media through print mechanism

24

C2162-67802 Stop Paper width adjustment stop - Adjusts for input paper width

25

C4549-40027 Actuator Clutch actuator - Pulls the clutch against the drive gear which starts the media picking process

26

C6450-40011 Spitton Spittoon - Holds ink expelled from cartridge during refresh cycle

27

C2162-40002 Gear Cluster gear for HP DeskJet 500 Series

28

C2162-20004 Spring Pivot spring - Provides tension for pivot to return to upright position

3

C2124-20001 Rail Rear rail - Supports carriage assembly

30

C2124-00009 Spring Spring - Installed in spittoon assembly

31

C2162-60009 Cable Cable assembly - Has 5-pin (F) connector on each end - 26.5cm (10.4in) long

32

C2162-67806 Spring Preloader - Applies downward pressure on drive shaft

33

C6450-60102 Sled Service station sled assembly - Mounts on top of the service station - Performs capping and wiping functions for the print cartridges

34

C6450-80052 Absorber Spittoon sponge - located in bottom of spittoon

35

C2124-20004 Spring Belt spring - For belt tension bracket

36

C2162-40036 Support Flex Support - Supports Flex Circuitry of Carriage Assembly

37

C2164-60045 Motor Paper stepper motor assembly (does NOT include cable)

38

C2124-80008 Strip Encoder strip - Clear strip with position marks - Used by the sensor in the carriage assembly to determine position

39

C2165-00001 Bracket Left bracket - Carriage rod adjustment bracket (Left)

4

C2128-40019 Peg Separator Peg - Lifts the separator pad when the lifter shaft lifts

40

C2128-60018 Separator Separator pad assembly

41

C4562-40032 Bracket Belt tension bracket - Pivot bracket for idler pulley - Applies tension to the carriage belt

42

C2124-00001 Spring Encoder spring - Provides tension for encoder strip

43

C2164-00015 Clip Carriage shaft retainer clip

44

C2162-40016 Hub Idler hub - Drive belt pivot point on left side of chassis

46

C2162-20005 Rod Carriage rod - Supports horizontal carriage movement

47

C2128-40020 Kicker Kicker - Straightens the stack of media in the input tray so that the separator can function consistently

48

C2164-40060 Belt Carriage belt for HP DeskJet 550C Series

6

C2124-60116 Roller Lower pinch roller

7

C4549-40029 Lifter Separator lifter

8

C2162-60006 Motor Carriage motor assembly (includes cable)

9

C2145-00017 Spring Lever arm spring - Provides tension between the lever arm and the pressure plate lifter

Printer parts diagram for: C2128-00002

C2128-00002 is represented by #15 in the diagram below.