CH971-91490Bar - Y-axis alignment bar - Includes fine-thread screws for adjusting the Y-axis alignment of the printheads - Located in front of the printheads
CH971-91629Bearing - Fmk Tool Bearing Carriage Install N
CH971-91640Bearing - Grit roll bearings kit - Includes 12 units
CH971-90710Belt - Carriage drive timing belt - Located between the carriage drive motor and the carriage drive shaft. Carriage Drive Timing Belt For HP DJ H35100 H35500 H45500 H45100 and similar Scitex Designjet model family types.
CH971-91530Belt - Drive belt - Used for the service station wiper motion
CH154-67015Bottle - Flush bottle - Squeeze bottle with label for UV flush
CH151ACleaner - lamp filters is suitable for HP FB950 printers. This is HP original part (number CH151A). Each filter is 14.3cm long 8.3cm wide and 0.3cm thick.
CH154-67045Clip - Clip assembly - Includes one unit, does not include the taller luer cap required for use with the clamp - Used on the printhead ink U-tubes - For use with Designjet H-series and Scitex FB950
CH971-91001Clip - Clip - Connected to the trolley and provides attachment points for the carriage drive belt on both ends
CH971-57327Connector - Complete ink tube/filter/connectors assembly - Used with the ink boxes - For use with Scitex FB950/FB500/FB700 and Designjet H (CS 5400uv) printers
CH971-91509Control Panel - Touch-sensitive color LCD control panel - Used on all Designjet H-series and ColorSpan 5400UV series printers
CQ114-67054Control Panel - Touch-sensitive LCD control panel - For the Scitex FB500/FB700 printer
L1Q41-67084Control Panel - FrmLcdU FRONT LCD PANEL
CH971-91634Coupler - Off-Head Supply (OHS) ink coupler - Includes one coupling and the nut used to secure it on the printer - This is the quick-disconnect attachment for the ink boxes and receives the connector from the inkbox pigtail
CH154-67005Encoder - Encoder strip actuator assembly - Includes bracket - Used in all lifting assemblies and service station - For the Scitex FB950 printer
CH971-90708Encoder - Encoder reader assembly - Located on the back of the carriage assembly
CH971-91425Encoder - Mylar encoder strip and foam tape - It is long enough for a 2.5m (98-inch) printer and can be trimmed down for smaller printers - Part requires you to reuse the existing aluminum bar from the old strip
CH108-60004Filter - Large cylindrical air filter - Located on the exterior of the vacuum assembly
CH971-91504Filter - Ink filter - 1.74-inch diameter - Can be used with any ink color - This filter is used in the OHS area of the printer - For use with Scitex FB950 and Designjet H-Series
CH971-91639Filter - Tube/filter/fitting assembly - Used between the printhead and the air manifold
CH971-91644Filter - Replacement filter - Includes media and mesh used inside the ShopVac, as well as related fasteners - For the Scitex FB500/FB700 printers
CQ114-67188Filter - Replacement filter - Includes media and mesh used inside the ShopVac, as well as related fasteners - For the Scitex FB500/FB700 printers
CH154-67043Hardware - ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer - When installing this part on some vintages, a power cable (included) must be replaced
CH971-90716Idler - Carriage idler assembly - Located on left end of the printer - Includes various parts and instructions describing how to remove and replace the item
CH971-91595Idler - Idler assembly - Located on service-end of the rail - For use with Scitex FB910/FB950 and the Designjet H-series
CH971-62940Insert - Pul Tmg Dbl Flngd W/Insert 3mm 20 Grv
CH971-62905Leg - Brace Table Leg Rght 13.31 Lg 0.625 Wd
CH971-62906Leg - Brace Table Leg Rght 13.31 Lg 0.625 Wd
VH120-60003Light - HP Designjet 788 Light Cyan Ink
CH971-90854Maintenance Kit - Grease kit - Used to lubricate gritroll bearings, media drive worm gear, and up/down threads of the media hold-down roller
901493MASTER - Master printhead - Does not include any thermistors - Used on any location of the printer - For use with Scitex FB950 and any model of the Designjet H series
CH971-57363PC Board - Brkt Carriage Piranha Head Pcb
CH971-91512PC Board - Power distribution board - Routes inbound AC to the various printer power supplies - For the Scitex FB500/FB700, and the Designjet H-Series
CH971-91542PC Board - Main controller board - Used for the Off-Head Supply (OHS) - Has sockets for the profilers
CH971-91493Printhead - Master printhead - Does not include any thermistors - Used on any location of the printer - For use with Scitex FB950 and any model of the Designjet H series
CH154-67006Reader - Encoder reader board - Does not include the metal bracket - This assembly is used on all of the lifting positions - For the Scitex FB950/FB500/FB700 printer
CH971-91586Relay - AC relay - Located in the main electronics box
CH104A-Repair_DesignJetRepair Service - Ship your product to us for a small diagnostic fee; and a professional service job. We will contact you with repair total and your diagnostic fee will be waived if unit is repaired. Service warranty is 30days labor and 90days for parts. Extended warranty option is available.
CH104-67001Reservoir - Printhead reservoir kit - For use when there is a reservoir leak, fitting problem, or other printhead issues, where jetting is not the problem - For use with any of the piezo-printhead engines
CH971-57266Reservoir - Vacuum reservoir - This is a portion of the ink system vacuum - For use with Designjet H series and Scitex FB950 printers
CH971-56942Service Station - Brkt Service Station Piranha Lbrkt Mnt
CH971-91529Service Station - Frm Service Station N
CH971-91577Shaft - Carriage drive shaft - Shaft is knurled to prevent pulley from slipping on the shaft - For the Scitex FB500/FB700/FB910/FB950 printer
CQ114-67110Shaft - Carriage drive shaft - Shaft is knurled to prevent pulley from slipping on the shaft - For the Scitex FB500/FB700/FB910/FB950 printer
CH971-91492Thermistor - Thermistors kit - Includes two ink and one air temperature thermistor (they have been calibrated together and should be replaced together)
CH971-55984Tool - Head height gauge tool - This go/no-go gauge is used to set the printhead height to 0.085-inches above the surface of the media
CH971-57693Tool - Custom tool - Assists removing and installing the main drive belt connection to the carriage
CH971-91631Tool - Service tools kit - Kit includes the head height gauge, squeeze bottle (for flush), lint-free cloths, luer caps, and the carriage belt - For use with Scitex FB950 and the Designjet H-series
CH971-15183Transformer - Step-down transformer (220VAC to 110VAC) - Used with the 110VAC ShopVac
CH971-91227Tube - U-tube - For use with ink between two printheads of a color
CH971-91499Tube - Short UV ink tube - Connects to the printhead with a luer fitting and to the ink track tube with multi-colored luer fittings
Repair It
Exchange It
View Supplies
Service Manual
